Do you know about - Why Ozone Use is a Must When Properly Treating a Mold question in a Home Or construction
Physical Therapy School! Again, for I know. Ready to share new things that are useful. You and your friends.Have You Been Told You Can complete a acceptable Mold Remediation task Without Using a High Level Ozone Shock Treatment?
What I said. It is not outcome that the real about Physical Therapy School. You check this out article for info on anyone wish to know is Physical Therapy School.How is Why Ozone Use is a Must When Properly Treating a Mold question in a Home Or construction
Think Again!! Says Nations Top Mold Remediation Expert, Quoting a military article Issued By Scientists at Los Alamos National Laboratory Which Proves Its approximately Impossible
Did You Know That Anthrax Reproduces With Toxic Spores Just Like Toxic Mold?
I Discovered That The Us military Has Studied How to De-Con a Civilian building Which Has Been Contaminated by a Spore Based Pathogen Like Mold. The Studies Were Conducted After the Anthrax Attacks on Congressmen Using the Us Post Office. Their Discoveries Throw approved Mold treatment Out the Window!
Ozone Myths Shattered!
Often I am asked about the effectiveness of Ozone treatments for mold remediation.This is a complex topic, which has many sides.
If you ask me is ozone productive for mold remediation I would of course answer, that it depends...
On what you ask? Well on many, many, things I answer.
You see there are some contractors out there that are using distinguished ozone generators as a substitute for the actual bodily steps of mold remediation. I have heard claims like:
"Our ozone machines are so distinguished they will turn mold to ash."
"They will of course vaporize mold."
"Leave the dry wall and the ozone cannons will destroy the mold which you can paint right over"
And Dozens of other lies.
The truth is the use of ozone alone is never a complete treatment for mold.
The roots of mold will perforate deep within a substrate up to 3/16ths to .5 inch.
Additionally even dead mold is still poisonous. So removing physically all of the structures of the mold organism is necessary. Just using a gas-out alone, will never achieve this objective.
Molds reproduce by production spores that cannot be seen without magnification. Mold spores waft straight through the indoor and outdoor air continually. When mold spores land on a damp spot indoors, they begin growing and multiplying, and soon the mold problem is out of control. Many types of molds exist. All Molds have the potential to cause health effects.
Ozone Kills Mold!
Ozone is a distinguished gas and it will destroy mold spores and the mVocs created by toxic bacterial or fungal organisms.
In fact according to a study conducted at Los Alamos National Laboratory (that's where they industrialized the atomic bomb) scientists discovered, that in order to truly complete the decontamination of a home school or commercial building that has been contaminated with a spore based pathogen, like mold it is of course vital to complete your decontamination process with the use of a gas-out that would flood the area with toxic levels of a reactive gas.
The calculate given is that a building has so many nooks crannies crevices and cul- de-sacs; it has so many surfaces that interface in the middle of boards and in ducts and others inaccessible spaces where spore can hide and remain eluded by liquid based disinfectants. That's right no number of Hepa vacuuming or air-scrubbing or manual clean up can ever achieve complete true de-con without a gas out due inaccessibility.
But a gas can over come this because at high levels the gas can perforate right into all the nooks and crannies and even into carpets and fabrics and other porous materials.
While many gases were carefully the winner was ozone hands down!
The calculate is uncomplicated ozone is lethal to virtually all pathogens- yet it is made of O3 which is pure oxygen O2 %2B O a singular free-radical oxygen molecule. The singular oxygen can only last for a split second when it bonds with and adheres to other molecules. With viruses mold and bacteria it punches a hole directly into the cell wall and then begins to destroy the contents. A great number of ozone is required for serious remediation.
If a high parts per million attentiveness of ozone is not reached within a given area, all the bacteria will not be killed. Mold will then grow once again from any remaining live spores, and strong odors may return. That is why we use Bio3 Blaster commercial grade distinguished commercial power ozone air generators. They are chosen by only the best professionals for serious mold, mildew, odor and pollutant removals in homes, offices, motel rooms, clubs, pubs, basements, cars, boats, as well as for fire, flood and crime scene cleanup restorations.
What is then left behind is pure oxygen O2... Safe and healthy.
The only way for this process to be productive is to detach an area and then to use distinguished ozone generators known as cannons to originate ozone at very high levels to completely saturate the air in the isolated area.
The Way its Done is With an Ozone Cannon!
No habitancy plants animals or fish can be gift when this is done.
Each room of the house can be blasted with an Ozone treatment to sterilize them of mold.
High powered ozone travels and kills mold and bacteria all straight through the room.
This process is known as High Ozone Shock Treatment.
It is not a substitute for mold remediation. If there is mold growing on sheet rock for instance ozone is not an answer. Mold will grow completely straight through sheet rock once the hyphal root penetrates the paper of the drywall it swiftly permeates the gypsum as it is made of calcium carbonate a mineral rich food source for mold. The mold approximately always penetrates the paper behind the wall too! If mold is growing in an attic, ozone alone is not an answer. For the same reasons the roots of the mold perforate the boards to deeply for ozone alone to completely destroy the problem.
What ozone is great for is to get into the areas where the human or fogger or Hepa vac can't and to destroy the spores that were missed.
As humans, trained mold workers lack eyes good enough to see the mold they are combating once it goes airborne. You see ten thousand spores can fit onto the head of a pin.
They are that small!!!
In one quadrate inch of flowering mold there can be everywhere from 1-5 million!!! What's worse is that when a mold employee begins to fog or spray the mold- the mold, has a built in survival mechanism called bursting or sporulation which allows it to send clouds of invisible spores into the air to fly the chemicals being sprayed onto them. This means that in a typical mold remediation job, millions and billions of spores are put into the air and are too tiny to see.
By saturating the area that the treatment has been performed in after the mold has been killed and treated only is one is assured of complete decontamination.
If you can stand to be in a room with an ozone machine it does Not have the power to kill mold and bacteria. You can Only kill mold by the use of unoccupied room High Ozone Shock Treatments.Mold can Onlybe killed by ozone levels much higher than meant for human career like our machines can produce.
This step should only be performed, after the gross extraction of the porous building materials like drywall, after the stains have been removed and after the surfaces have been fogged and or vacuumed.
Ozone will also permanently destroy the mVoc's and musty odors.
Ozone oxidizes poisonous materials rapidly; sterilization quality is 600--3000 times stronger than Chlorine. Ozone kills E-coli 3125 times faster than chlorine. Some swimming pools/spas use ozone because it is a strong disinfectant, but it converts back into oxygen so it does not have harmful effects like chlorine. The proof of the efficacy of Ozone Shock therapy can be found in a study published in the Journal of the International ozone Association.
Many mold remediation fellowships use zero or no sporicidal products (things that kill spore or mold "seeds") to achieve a mold remediation process. That means They always leave behind spore-contaminated structures.
Killing the spores is the most foremost part of a mold remediation process!!!!
Leaving the spores behind is like planting hereafter mold problems which will inevitably compose or germinate later.
Safe Mold Solutions(Tm) recommends no less than two sporicides (things that destroy spores) be used.
We have found the use of both Ozone and hydrogen peroxide to be ideal.
Both ozone and hydrogen peroxide work nearly identically. Both use free radical oxygen to destroy mold viruses bacteria and spores. Hydrogen peroxide leaves behind water, ozone leaves behind only pure oxygen.
No Residues... Safe and Effective!!!!!
What does all this mean?
If you have allergies to bacteria and mold or are suffering from contamination you can only sanitize, and truly destroy, these contaminants buy the use of an unoccupied room high Ozone Shock Treatment. Once you have shocked the unoccupied room or area you can then return an hour after the machine is turned off to breathe and sleep best in the room that has been sanitized. No air purifier or chemical can do that for you!!!
We suggest the use of the machines that only Elite professionals use to kill mold spores in high humidity and flooding situations. The use of high powered ozone shock treatments is the Only way to reach hard to get to areas to kill mold spores.
If a competitor offers you a mold clean up protocol without Ozone Shock Treament- kick him out of your home!!! He obviously doesn't understand mold or its' complete and acceptable clean up!
I hope you receive new knowledge about Physical Therapy School. Where you can offer easy use in your day-to-day life. And most of all, your reaction is Physical Therapy School.Read more.. the full report Why Ozone Use is a Must When Properly Treating a Mold question in a Home Or construction. View Related articles associated with Physical Therapy School. I Roll below. I even have suggested my friends to help share the Facebook Twitter Like Tweet. Can you share Why Ozone Use is a Must When Properly Treating a Mold question in a Home Or construction.
No comments:
Post a Comment